With the development of trade, the safety and quality requirements of buyers and consumers are constantly improving. The Malaysian government stipulates that suppliers should apply for product certification if the products are regularly transported to Malaysia. In 1998, Malaysia promulgated a new "communications and multimedia Act 1998", which specifies in detail the access conditions of Malaysia's telecommunication service and communication market. At the same time, Malaysia communications and Multimedia Commission (CMC) was born. According to the law of communication and multimedia, when the communication equipment is put on the market, it is necessary to apply to CMC or the certification authority designated by CMC for type approval and obtain the equipment certification certificate and certification mark.
SIRIM is the only certification authority in Malaysia. Any factory or company can apply to SIRIM, and audit and obtain approval according to the recognized standards under the product certification system. These certifications are voluntary, but in many cases, mandatory certification will be required at the request of government administration.
According to the regulations on approval of communication equipment and electrical equipment, the following 31 categories of products shall be subject to mandatory type approval and safety certification respectively: plug (less than 15 A), switch and dimmer, socket (15 The main components are as follows: A, mixer, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric heater, electric , immersion heater, high fidelity device, mosquito repellent, bread oven, electric fan, TV set, vacuum cleaner, player, washing machine, refrigerator, rice cooker, Christmas lamp, household electric tools, wires and cables (cross section area: 0.5 ~ 35 mm2).
The new subcategories include: doorbell and doorbell, portable cable reel, screw socket, strip luminaire (except tube / bulb), self ballasted fluorescent lamp luminaire, screw or bayonet self ballasted compact fluorescent lamp (CFL), common LED and safety of lamp control device below 250V DC and / or 1000V AC, special requirements for DC or AC electronic control device of LED module, LED module for general lighting Block (e.g. double ended self ballasted LED lamp), single ended self ballasted LED lamp for general lighting with voltage above 50V, night lamp with plug, portable LED lamp, bottle heating sterilizer, drinking water dispenser / filter, dishwasher and other appliances, decorative fan and separate pressurizer and vaneless fan, ion steamer or similar equipment, audio / video recorder below 4 channels, it equipment adapter It adapter, it adapter, electronic switch adapter, etc.
Communication equipment testing section (CETs) under the jurisdiction of SIRIM is responsible for the specific certification of communication equipment type approval. SIRIM is the only certification authority in Malaysia. All electronic products entering Malaysia need to apply for SIRIM certification certificate. In principle, the applicant should be a local institution in Malaysia. SIRIM QAS international is responsible for the application and management of SIRIM certification, which issues the SIRIM certificate. The contents of SIRIM certification include:
1. Electrical safety;
2. Electromagnetic compatibility, frequency below 30kHz, between 26khz and 1300 MHz, and above 1000 MHz;
3. Coordination of telecommunication network, including public switching network, cellular telephone network, data communication network and communication software;
4. Wireless communication, frequency below 30kHz, between 26khz and 1300 MHz, and above 1000MHz;
5. Optical communication;
Cables and accessories.
SIRIM certification mark
top logo, voluntary
Malaysia voluntary certification mark
st logo, mandatory
Malaysia compulsory certification mark
SIRIM certification content
type approval contents include situation report evaluation, laboratory test, on-site test, if the equipment is only used for exhibition and demonstration, the application can be submitted to CMC of communication and multimedia Committee, and the special certification certificate can be obtained directly through the evaluation of written report.
recently, SIRIM has revised some terms in its certification process. The main modifications are as follows:
The SIRIM certificate must now be reviewed once a year, and the maximum validity period is 5 years;
2. Corresponding to Article 1, the submission of test reports only accepts the test reports from qualified laboratories (e.g. Moore's laboratory) whose issuing date is less than five years;
equipment approved by SIRIM for more than 5 years, if it still needs to be sold in the Malaysian market, it must be sent back to the laboratory for testing and submit SIRIM application again. The original SIRIM certificate will be expired and invalid;
in the application process of SIRIM certification in Malaysia, product testing can be completed through Moore's laboratory, or it can be converted into SIRIM approval by submitting CB report and certificate. In this case, it is generally unnecessary to submit samples for testing again, but sometimes SIRIM will ask customers to send samples to check the consistency between the samples identified on the original report and the samples submitted.
CB certificate and test report can be submitted for the following qualifications:
1. A domestic or foreign manufacturer or
Agent authorized by manufacturer
the following documents need to be submitted:
complete signed and approved Product Certification Questionnaire
Copy of CB test report
after receiving the above documents, the quotation of application fee and factory inspection fee will be informed
when the quotation is agreed, the applicant shall provide the product certification application form
samples are not required if not required
the first factory inspection must comply with the product certification system. Once it meets the requirements, the certificate will be issued
the validity period of the certificate is one year. In order to ensure the renewal of the certificate, the annual inspection must be carried out
Market supervision is also implemented
subsequent sample testing may occur
complaints and complaints NCB shall be submitted in writing to the general manager of sirimqas certification and Inspection Services Department.
SIRIM certification factory inspection
factory inspection is required,
the first factory inspection must comply with the product certification system. Once the conformity is met, the certificate will be issued
the validity period of the certificate is one year. In order to ensure the renewal of the certificate, the annual inspection must be carried out.
SIRIM certification cycle
regular for 3-5 weeks, can be expedited, urgent need to pay additional fees.
